Motorcycle handle grip,hot grips,heated grip,ATV grips,handle bar end,Crash ball bar ends or handlebar end,China motorcycle grip supplier  
Motorcycle handle grips supplier in china, motorcycle handlebar grip, ATV grips, Scooter grip, heated grips,bicycle grip, grip sponge and grip parts...
 
   -Home |Motorcycle grips |Motorcycle Heated Grips |Grips Sponge |Handle bar End |Bicycle Grip |Grips Knowledge |Contact
 
 
 
 

 
 

Motorcycle handle grips knowledge

(A). How to Replace Motorcycle Grips:
It is easy to replace Grips, for instance are good example. It only involves few steps and here they are:
1.Ready your new grips, rubbing alcohol, hammer, socket and WD-40.
2.Remove the bar end. Be careful with its head and threads. If they are already damaged, better replace them also.
3.Pull the end of the grip and spray on the WD-40 to loosen the contact. You can remove the grips by twisting and folding its inner edge. Remember where the original location of the inner edge.
4.After the grip has been pulled, clean the handle with rubbing alcohol. Be sure to remove the glue from the Clip-on. Also, lubricate the Clip-on with rubbing alcohol and slide the new grip. While sliding it, do some twisting techniques. Do this while the alcohol has not yet evaporated otherwise it will be harder to twist.
If the new grip material will allow, you can also use oil instead of alcohol.
5.To tap the new grip into position, use the hammer and socket. Make sure that it fits well and will not impair the bike's operation. To test it, roll the throttle to full-on and let it snap back. You can ride around to be used to its stiffness.

(B). Basic Grip Installation Method:

One item that you need to replace in your ATV is the pair of ATV grips. The best thing about this ATV part is the fact that you have plenty of choices to suit your comfort and style. Adding them to your machine can really be exciting. It gives you different hype, too. Putting on new grips can be made as easy.

While there are many different methods used by many riders, this one can be very useful especially to neophyte riders. Let’s start with the items you will need. Basically the following materials are used:
(• Water • Paper towels • Grip glue • Scissors • Dish soap • New grips)

The first step is of course to remove the present grips. You do this by using sharp scissors to cut around the end of the grip that is furthest away from the handlebars. Slide one of the scissors’ blades under the grip and cut. Your pair of scissors must be sharp enough to do the cutting. Toss the old grips aside as you are finished hacking them away.

Next up, you will need to take your razor and slide them down the grip at the top and at the bottom of it. You may need to slice it several times depending on the amount of glue that was put on it. When the grips are taken off, toss them aside for the next step.

Now that the old grips are taken off, you will need to clean the area where the grips go. It is a must that you get rid of all the excess glue of each side. You can use a rag and water to take it off. Elastic glue type of material is easy to remove.

When you believe that everything is clean, putting on the new grips can follow immediately. Initially, you will need to take both grips and go to a sink. Put them aside and apply soap all around your middle finger and then smear the soap around it with your other hand. Dry the hand that doesn’t have the soap on your middle finger so you don’t get soap on the outside of the grip when you grab it, and put your middle finger inside one of the grips making sure you have soap all around the sides of the grip. Put the grip down so that the entrance of the grip is in the air. Now, you need to clean your hands so that there’s no soap on them. As you look at the grips you’ll find out that one hole is bigger than the other. The right grip where your throttle tube is placed has the bigger hole.

Now you are ready to install your new grips. First, you need to slide your left grip on and slide it back off. Same thing must be done with the right grip. This is to make sure that you put on the right end, and to lube the bar. Make streaks of glue going from where the top of the grip would be. Six streaks would be efficient. Side the grip all the way on slowly. Subsequently, pull the sides of the grip so that the grip doesn’t just push all the glue up, but it normally goes on top of the glue. You can use towel to remove the excess glue. Let the grips rest for a minimum of 8 hours untouched until the glue becomes dry.

Test your vehicle to know if the installation is securely and effectively made.

 
 

 
Featured Grips
 
 



 
             
   

Copyright © 2000-2010 Motorcycle-Grips.Com All rights reserved
Phone: 86-574-2781-1158 Fax: 86-574-8814-6069
Ningbo City. Zhejiang Pro. China
Email: Commercial@motorcycle-grip.com MSN:kathyqin625@hotmail.com
Yahoo ID: Cyclepartscn@yahoo.com Skype: Solatkathy

     

 
Motorcycle Grips | Motorcycle Heated Grips | Heated Grips | Ebike Grips | Grips Sponge | Handle Bar End | Bicycle Girps | Grips Parts | Motorcycle Battery | Sitemap | Links | Grips Directory | Motorcycle parts | Motorcycle accessories | Motorcycle aluminum Sprockets | Motorcycle Parts Exporter| Electric Appliance | Motorcycle Parts | Bicycle Parts | Motorcycle Handlebar| Motorcycle Sprockets | Motorcycle Battery Charger |